« previous next »
Pages: [1]

Author Topic: Headrest Parts  (Read 5749 times)

cobaltfan

  • Guest
Headrest Parts
« on: July 20, 2011, 04:39:35 »
Hi there.  I have a 1971 280sl and am looking for a part on the seat headrest.  I have been unable to locate a part number - maybe one of you can help me out.

There are holes on each side of the headrest and at one time it appears there was some type of cover over them.  Anyone know what I'm talking about - may take a photo if it will assist in identification...

Thanks!
Logged

treedoc

  • Guest
Re: Headrest Parts
« Reply #1 on: July 21, 2011, 23:09:28 »
Hi Koboltfan.

See below head rest image from our 280SL built 10/1970
Suggest you contact "Woody" at the Irvine CA, Classic Centre,  949 598 4845
New parts unlikely to be still available, if no luck check on Ebay for used head rests.

Logged

wwheeler

  • Vendor
  • Platinum
  • ******
  • USA, TX, Dallas
  • Posts: 2898
Re: Headrest Parts
« Reply #2 on: July 26, 2011, 19:36:54 »
There are some small parts that guide and apply friction to the rods and can be bought from the Classic Center. I would recommend changing those while you are at it.

Headrest friction pads #115 975 00 23

Good luck.
Logged
Wallace
Texas
'68 280SE W111 coupe
'60 220SE W128 coupe
'70 Plymouth Roadrunner 440+6

star63

  • Full Member
  • Senior
  • ***
  • Finland, Etela-Suomen Laani, Vantaa
  • Posts: 243
Re: Headrest Parts
« Reply #3 on: July 16, 2012, 08:06:48 »
Could someone explain what is the function of the side-holes?
Can those be added to head rests that don't have them?
Logged
Petri
'67 250 SL (early)
'66 230 SL (long project)
Finland

hkollan

  • Associate Member
  • Gold
  • *****
  • Spain, Castilla-La Mancha
  • Posts: 519
Re: Headrest Parts
« Reply #4 on: July 17, 2012, 09:36:11 »
They are there to give access to the  two 10mm head "thightening screws".  The later style headrests introduced around 1972 had a sort of selftightening mechanism and therefore no need for the access-holes on the side.

Hans
Logged
Hans K, Cuenca, Spain
1968 280 SL 387 Blue met., parchment leather
1971 280 SL 462 Beige met, Brown leather
1968 280 SL 180 Silver, Red leather
1964 300 SE Lang 040 Black w/Red leather
1985 500 SL 735 Astral Silver w/Black leather
1987 560 SEC 199 Black met., Black leather

star63

  • Full Member
  • Senior
  • ***
  • Finland, Etela-Suomen Laani, Vantaa
  • Posts: 243
Re: Headrest Parts
« Reply #5 on: July 17, 2012, 21:25:10 »
Thanks !

- Petri
Logged
Petri
'67 250 SL (early)
'66 230 SL (long project)
Finland

114015

  • Full Member
  • Platinum
  • ******
  • Germany, Nordrhein-Westfalen, Tecklenburg
  • Posts: 2080
Re: Headrest Parts
« Reply #6 on: July 18, 2012, 11:42:11 »
Quote
There are holes on each side of the headrest and at one time it appears there was some type of cover over them.  Anyone know what I'm talking about - may take a photo if it will assist in identification...


Hello Koboltfan,

These nice access holes to the 10 mm hex screws which Geoff showed are not separately available and they have never been.
You have to find a set of headrests with them or try to fabricate those on your own... :'(


Achim
Logged
Achim
(Germany)

66andBlue

  • Full Member
  • Platinum
  • ******
  • USA, CA, Solana Beach
  • Posts: 4735
Re: Headrest Parts
« Reply #7 on: July 19, 2012, 04:53:27 »
The "tightening screws" that Hans describes adjust the friction between the walls of a cylinder in the head and a bushing attached at right angle to the rods that anchor the headrest in the seat.  This photo shows the individual parts:
Logged
Alfred
1964 230SL manual 4-speed 568H signal red
1966 230SL automatic 334G light blue (sold)
1968 280SL automatic (now 904G midnight blue)
Pages: [1]
« previous next »