Author Topic: Accelerator pedal (Read 7442 times)

romeks · « **on:** March 08, 2016, 22:10:35 »

Hi Everyone,

Could you help me how to deal with instoll basis of accelerator pedal and tank lid like on the photos. Let me know where I can find out on this forum.

Thanks in advance,

Romeks

Shvegel · « **Reply #1 on:** March 18, 2016, 16:40:31 »

Romeks,
The cover for the fuel tanl level sender is incorrect. The correct one is a plastic cover that just presses in place. The cover shown is for the 2 large holes in the body under the rear seat. As for the accelerator pedal the rubber pedal just pushes into place. You might have to pound on it a little with your hand.

perry113 · « **Reply #2 on:** March 18, 2016, 17:52:55 »

It's hard to tell from photos nut it looks like you have a new provision for your gas pedal that has yet to be welded to you floor pan.

Shvegel · « **Reply #3 on:** March 18, 2016, 21:57:50 »

Here is a picture of the fuel sending unit cap.

mBdrvr · « **Reply #4 on:** March 19, 2016, 13:47:36 »

My car has new floors but no fitting for the accelerator pedal. Any suggestions on what to do for a replacement? MB does not have the part.

Shvegel · « **Reply #5 on:** March 19, 2016, 22:41:06 »

Dan at Benz Barn or Gernold at SL tech should be able to sell you a used one.

perry113 · « **Reply #6 on:** March 19, 2016, 23:03:00 »

Quote from: mBdrvr on March 19, 2016, 13:47:36

My car has new floors but no fitting for the accelerator pedal. Any suggestions on what to do for a replacement? MB does not have the part.

Try K & K Manufacturing part # 113-301-00-02

see:

http://www.kkmfg.com/catalog_loader.php?page=113/113FrameFloors.svg

romeks · « **Reply #7 on:** March 20, 2016, 14:11:41 »

Thank you very much for your answers. Thanks to your advice now I have clear situation what decision i should make. In upcoming weeks I am going to install engine and I will show you photos of the progress

Best regards
Romek

romeks · « **Reply #8 on:** March 21, 2016, 11:41:25 »

Shvegel,

Thank you for your correct information. After that I find and order proper cap from SLS:
[80] Cover above fuel sender, plastic,black

Cover above fuel sender, plastic,black

Art.Nr.:347014

Romek

mBdrvr · « **Reply #9 on:** March 21, 2016, 17:40:32 »

Thanks for the info.

dirkbalter · « **Reply #10 on:** April 15, 2016, 21:46:27 »

Romec,
If the accelerator bracket location is still in question, I can send you some pics of mine. I removed and re-welded it when I did the floor panels.
Dirk

mBdrvr · « **Reply #11 on:** April 16, 2016, 13:33:34 »

Dirkbalter:

Can you post the picture??

Thanks,

Paul

dirkbalter · « **Reply #12 on:** April 16, 2016, 20:23:20 »

Here is,
Dirk

dirkbalter · « **Reply #13 on:** April 16, 2016, 20:24:59 »

dirkbalter · « **Reply #14 on:** April 16, 2016, 20:27:09 »

romeks · « **Reply #15 on:** May 18, 2016, 12:30:55 »

Hi Dirk,

Many thanks for your good advice. The pictures were very helpful for me.
I attache some picters of my work which I did with your help.

I have one more problem to resolve, if you have aircondition.
Could you send me a pictures where the pipe for drip tray(excess water) is place in the floor?

I would be very grateful for your answer.

Romek

Shvegel · « **Reply #16 on:** May 18, 2016, 13:08:25 »

According to the Frigiking installation manual it is a 35mm hole in the corner of the floor with no measurements given. If you do not have the large rubber ring(Grommet) that fits in the hole you may want to make a smaller hole.

romeks · « **Reply #17 on:** May 19, 2016, 08:43:53 »

Hi Shvegel,

Thank you for your quick answer about pipe of airconditioning. I will do hole 20 mm in the corner of the floor according your advice

Regards,

Romek

dirkbalter · « **Reply #18 on:** May 27, 2016, 18:13:12 »

Romek
Sorry for the delay.
I saw that you got help already. (I don't have AC.)
Dirk

News:

Author Topic: Accelerator pedal (Read 7442 times)